Tel: (091) 773422 Fax: (091) 773946

METPOINT® OCV

Home ShopBEKO TECHMETPOINT® OCV
METPOINT® OCV

METPOINT® OCV

The METPOINT® OCV has been developed for measuring hydrocarbon vapours and gases in compressed air system applications. The detection levels are as low as one thousandth mg/m³ of residual oil vapour content and are executed continuously in ongoing operation. Shortened measuring intervals enable the rapid and reliable display of even the smallest deviations.

This on-line monitoring process provides the certainty about the quality of your compressed air as an important element of your process safety at all times and at all quality-critical system points.

The measurement data can be utilised for documenting the compressed air quality and for identifying contamination sources. The oil vapour measuring can be implemented with two various products: METPOINT® OCV and METPOINT® OCV compact. The similarities and differences will be explained in detail in this brochure.

Send a Quote Request
Categories: , , .

METPOINT® OCV and METPOINT® OCV compact enable us to provide two products with which you can permanently measure the quality of your compressed air with regard to the oil vapour content.

Advantages of the METPOINT OCV | OCV compact

The details will be clarified more precisely on the following pages. Installation example with METPOINT

  • Safe
    • Reproducible accuracy of the measurement values by utilising reference gas generation (catalytic converter principle)
    • Automatic monitoring for the reference gas and sensor electronics
    • Issuing and transferring of alarm signal messages

 

  • Reliable
    • Pressure range from 3 to 16 bar
    • Online monitoring for the oil vapour concentrationData transfer to display as standard feature and control centre with customary communication methods

 

  • User-friendly
    • Visualisation of all measurement values
    • Flexible installation

 

There are however certain differences, which can qualify them more efficiently for the respective application purpose.

TECHNICAL DATA

Item METPOINT OCV METPOINT OCV compact
Measuring and display unit Separated, connected with data cable (maximum 5m) One unit with a robust industrial design
Protection class IP20 sensor unit
IP54 display unit		 IP54
Updating the measuring value display Every 2 minutes Every 4 seconds
Gas flow through rate 2 – 3 Standard litre / minute, relating to 1.0 bar absolute and +20°C
bei 1 bar abs / 20°C		 Approx. 1.20 Standard litre / minute relative to 1.0 bar absolute and+20°C
Interfaces 4…20 mA, Ethernet 4…20 mA, RS485/Modbus (only for measuring value)
Display and operating concept Menu-guided on colour touch screen 7-Segment display with 5 buttons forsetting configuration and alarm
Optical display for the operating status Coloured representation
on touch screen display		 3 LEDs (each red/green) for purifier,PID and oil class
Measuring cell protection Utilising error indicator
on display		 The measuring cell will be protected against too high oil content via a valve switching process

ADDITIONAL INFO

Recognised procedure and external test certificate

The eligibility of the utilised measuring procedure in the METPOINT® OCV for the continuous recording of hydrocarbon vapour and gases in compressed air will be executed via comparison measurements in the PID procedure with reference procedures according to:

›› ISO 8573-5

›› Pharmacopeia (Ph. Eur. 2.1.6)

While the reference procedures according to ISO 8573-5 and the pharmacopoeia are based on a discontinued sampling method, the METPOINT® OCV measuring procedure provides the advantage of on-line monitoring. This therefore creates the prerequisite to immediately react to an increase in the residual oil content in the compressed air and possible breaching of the limiting values. The METPOINT® OCV is the first TÜV certified on-line system for recording the oil vapour content in compressed air. It has been certified by TÜV NORD according to the requirements ISO 8573-1.

Simple and safe operation

Both METPOINT® OCV systems provide output information about the current measurement value (oil vapour in mg/m³), the ISO 8573 oil class as well as the status of the measuring system and its components. In addition, the status of the measuring cell and the purifier will be displayed visually. You therefore have an overview about the measurement values, oil class, system status at all times and know immediately that your compressed air is correct.

Related products

 View Details

METPOINT® PRM
, ,
View Details

METPOINT BDL portable
, ,
View Details

METPOINT® FLM
, ,
View Details

Minimum pressure valves
, ,

ABOUT C+L INDUSTRIAL

Established in 1998 with the head office in Galway, C&L provide their customers with a range of products and services that are second to none.

Industry knowledge and expertise are guaranteed with key personnel contributing some 30 years of industry experience and know-how to the business.

Contact Info

QUICK LINKS

  • AIR COMPRESSORS
  • BLOWERS
  • VACUUM PUMPS
  • EXTRACTION
  • AIRNET PIPING
  • COMPRESSED AIR TREATMENT

SIGN UP TO OUR NEWSLETTER

© 2020 · C&L Industrial Ltd | Developed by DevoutDigital